Take your interior cleaning to THE MAX!
|
|
Take a look at some of the tools in action.
We stock OEM parts for Tornador tools!
We also service and repair (while you wait).
We strongly suggest you DON'T use any citrus-based cleaners inside this unit as it tends to break down the inner intake tube in the bottle.
Air Requirements
The TORNADOR® Black cleaning tool requires a constant air pressure between 5.5 and 6.3 bar 78 to 90 psi, for optimum performance.
DO NOT EXCEED 90 psi.
CAUTION: Constant air supply rates vary depending on the size and power of the compressor.
Always make sure tank and air lines are free from impurities, oil and water contamination.
DO NOT EXCEED 90 psi.
CAUTION: Constant air supply rates vary depending on the size and power of the compressor.
Always make sure tank and air lines are free from impurities, oil and water contamination.
Instructions For Use
Cleaning Fabric (Seats, Rugs, Etc)
1. First, remove large debris and vacuum area to be cleaned.
2. Then turn liquid air valve to upright position to deliver cleaning solution.
3. Hold cleaning nozzle 1 to 3 inches from area to be cleaned. Fully depress trigger. Begin with overlapping motion over area to be cleaned.
4. Next turn valve to down position using just air and dry the area.
Cleaning Dashboard & Hard Surfaces.
1. Recommended air pressure set at 75 psi
2. Turn liquid valve to straight up vertical position, using a overlapping motion, spray area to be cleaned.
3. Allow cleaning liquid to remain on surface for 10 -15 seconds.
4. Follow with air only by turning valve to the horizontal down position. Begin drying with overlapping motion followed with a soft dry towel.
Few steps to help keep it running like new
Avoid dropping the gun on the floor, disconnect when not being used.
• Turn liquid valve to the horizontal position after use to avoid dripping from tip.
• Tighten the jar while holding the lid to avoid loosening or stripping gun assembly.
• Keep the cone of the gun clean by removing the cone and rinsing frequently.
After every use, place nozzle 2-3 inches into a bucket of soapy water while depressing the trigger once or twice to quickly remove dirt buildup in the cone.
This will prevent premature wear.
1. First, remove large debris and vacuum area to be cleaned.
2. Then turn liquid air valve to upright position to deliver cleaning solution.
3. Hold cleaning nozzle 1 to 3 inches from area to be cleaned. Fully depress trigger. Begin with overlapping motion over area to be cleaned.
4. Next turn valve to down position using just air and dry the area.
Cleaning Dashboard & Hard Surfaces.
1. Recommended air pressure set at 75 psi
2. Turn liquid valve to straight up vertical position, using a overlapping motion, spray area to be cleaned.
3. Allow cleaning liquid to remain on surface for 10 -15 seconds.
4. Follow with air only by turning valve to the horizontal down position. Begin drying with overlapping motion followed with a soft dry towel.
Few steps to help keep it running like new
Avoid dropping the gun on the floor, disconnect when not being used.
• Turn liquid valve to the horizontal position after use to avoid dripping from tip.
• Tighten the jar while holding the lid to avoid loosening or stripping gun assembly.
• Keep the cone of the gun clean by removing the cone and rinsing frequently.
After every use, place nozzle 2-3 inches into a bucket of soapy water while depressing the trigger once or twice to quickly remove dirt buildup in the cone.
This will prevent premature wear.
Need parts?
|
|
|
We stock OEM replacement parts.
Please ensure to include part number(s) in order.
| Tornador Black / Parts List |
| Tornador Classic / Parts List |
Call 1-800-537-8931 for additional information!
Product(s) subjected to change without notice.
Price does not including shipping.
Tornador is owned by ECP.
Price does not including shipping.
Tornador is owned by ECP.